| Make | Terex | | Model | TR60 | | Year | 2007 | | Hours | 578 h | | Useful load | 60 T | | Condition | / | | Price excl. VAT | 337,158 | | Location | USA | | Comments | OPTION BODY WEAR PLATES, HALF WEIGHT (3/8 INCH FLOOR, 1/4 INCH SIDE,1/4 INCH FRONT, 3/8 INCH END.
Detailed Description : Engine
Make / Model Cummins QSK19-C650
Type 4 cycle, turbocharged/aftercooled
Gross power @ 2,100 rpm (SAE J 1349) 650 hp (485 kW)
Net power @ 2,100 rpm 645 hp (481 kW)
Engine emission meets Tier III USA EPA / CARB MOH 40 CFR 89 and EU non-road mobile machinery directive. Stage 3.
Transmission
Allison M6610AR automatic electronic control with Soft Shift feature. Planetary gearing with six speeds forward
and two reverse. Integral TC 682 torque converter with automatic lock-up in all speed ranges. Hydraulic Retarder.
With body up, gear range is limited to 1st forward. Speeds with standard differential
Brakes
SERVICE – All hydraulic brake system control. Transmission mounted pressure compensating piston pump provides hydraulic pressure for brakes and steering. Independent circuits front and rear. Each circuit incorporates a nitrogen/hydraulic accumulator which stores energy to provide instant braking response.
Front: Dry Disc, diameter 28 in (710 mm)
Pad area, total 216 in2 (1,394 cm2)
Rear: Terex oil cooled, multiple disc, completely sealed from dirt and water.
Braking surface, total 7,308 in2 (47,151 cm2)
PARKING – Rear brakes applied by spring loaded opposing piston on disc pack, hydraulically released.
RETARDATION – Modulated lever control of rear disc brakes or hydraulic retarder in transmission. 900 hp (670 kW) continuous retardation.
SECONDARY – Park push button solenoid control applies service and parking brakes. Automatically applies when engine is switched off.
Parking brake applies when system pressure falls below a pre-determined level. Brakes conform to ISO 3450, (SAE J 1473).
Longitudinal "V" type floor with integral transverse box-section stiffeners.
The body is exhaust heated and rests on resilient impact absorption pads.
Full time exhaust is optional. Body floor wear surfaces are high hardness
(450 BHN) abrasion resistant steel, of yield strength 174,000 psi
(1,200 MPa). All other wear surfaces are high hardness (360-440BHN)
abrasion resistant steel, of yield strength 145,000 lbf/in2 (1,000 MPa).
Weights
Chassis, with hoists 67,460 lbs (30,600 kg)
Body, standard 23,480 lbs (10,650 kg)
Net Weight 90,940 lbs (41,250 kg)
Payload, maximum 120,000 lbs (54,430 kg)
Maximum Gross Weight* 210,940 lbs (95,680 kg)
FOR UNIT EQUIPPED WITH OPTIONAL HEAVY DUTY ROCK BODY:
Chassis, with hoists 67,460 lbs (30,600 kg)
Body, heavy duty, rock 29,100 lbs (13,200 kg)
Net weight 96,560 lbs (43,800 kg)
Payload, maximum 114,380 lbs (51,880 kg)
Maximum gross weight* 210,940 lbs (95,680 kg)
*Maximum permissible gross vehicle weight with options, attachments,
full fuel tank and payload.
WEIGHT DISTRIBUTION Front Axle Rear Axle
Empty 48% 52%
Loaded 34% 66%,
Drive : 2WD,
Horse Power : 450, |
|
Click on photo to enlarge
  Services
Tools |
Back 
